Solar Energy Demonstrator
Product Code : JA-LABCS-9623
The Solar Energy Demonstrator is a stand-alone photovoltaic trainer. A 30 Wp, 12 V solar panel charges a fused 12 V, 12 Ah sealed AGM battery through a 10 A charge controller. A 150 W pure sine inverter turns the battery DC into AC for the loads. Students follow the power from sunlight to the AC lamp with voltage, current and power readings.
Specifications of the Solar Energy Demonstrator
| Product code | JA-LABCS-9623 |
|---|---|
| Topics covered | Solar cell operation, battery storage and DC to AC conversion |
| Solar panel | 30 Wp nominal, 12 V module, rated at standard test conditions; on a panel stand |
| Battery | 12 V, 12 Ah sealed AGM battery, fused |
| Charge controller | 10 A |
| Inverter | 150 W pure sine wave; output voltage and frequency to suit the destination |
| Loads | DC and AC lamps or resistive loads |
| Monitoring | Voltage, current and power readings |
| Terminals and guide | Guarded terminals; user guide |
| Optional accessory | Irradiance meter for panel efficiency experiments* |
| Manufacturer | JaincoLab, Ambala, India |
* Standard JaincoLab specification for new builds.
Using the Solar Energy Demonstrator in practical classes
- Power at each stage. In steady sun, note the voltage, current and power of the panel, the battery and the load. Work out what share of the panel power reaches the AC lamp and where the rest is lost.
- Tilt and light level. Set the panel stand to several angles and note the panel current at each one. A Digital Lux Meter held beside the panel gives a relative check of the light on it. With the optional irradiance meter, students can also work out the panel efficiency.
- Charging record. After a load test, charge the battery from the panel and log its voltage with a Digital Multimeter every half hour. Plot the voltage against time.
- One cell and the panel. Measure a single cell on the Solar Cell Characteristics Apparatus. Compare its open-circuit voltage with the panel reading to estimate how many cells are in series.
Frequently Asked Questions
Can the 30 Wp panel recharge the 12 Ah battery in one day?
In clear weather it usually can, from a part-discharged state. In full sun the panel gives a little under two amps into the battery. Refilling half of the 12 Ah capacity then takes most of a sunny day. Cloud, dust on the panel or a poor tilt make it take longer.
Why does the demonstrator use a pure sine inverter rather than a modified sine one?
A pure sine output is close to mains, so lamps, small motors and chargers run as they would on the grid. Its waveform also looks clean on an oscilloscope. A modified sine output is a stepped wave. Some loads hum or run hot on it, and it is harder to teach from.
Why is a sealed AGM battery used instead of a flooded lead-acid battery?
An AGM battery holds its electrolyte in glass mats, so it does not spill and needs no topping up with water. It gives off very little gas in normal charging. That suits a classroom bench, where a flooded battery would need acid handling and good ventilation.
How deeply should students discharge the battery in load tests?
Keep load tests shallow. Lead-acid batteries, AGM types included, last far longer when they are not run flat. Stop a test while the battery still holds well over half its charge, and recharge it the same day rather than leaving it part-empty.
Which battery and charge controller ratings should a tender give for this trainer?
Give a fused 12 V, 12 Ah sealed AGM battery and a 10 A charge controller. Add a 30 Wp, 12 V panel rated at standard test conditions. Name the 150 W pure sine inverter with the output voltage and frequency your sites use. Our tenders page takes the full schedule.
Can the inverter output be matched to the mains of our country?
Yes. The 150 W pure sine inverter is fitted for the output voltage and frequency of the destination. The AC lamp and loads then match local mains. Give the country, voltage and frequency in your enquiry, and the inverter is chosen to suit.
Other solar energy trainers in the range
See the Renewable Energy Equipment range and more physics apparatus from JaincoLab, a physics lab equipment manufacturer in India.
For a quotation, send the product name and the quantity you need through our contact page. For tender or project supply, see our tenders page.
