• +91-85699-09696

categories

Analog Electronics Trainer Manufacturer, Suppliers and Exporter in India

Jaincolab Manufacturers is leading Analog Electronics Trainer Manufacturer,and supplier and Exporter in India, Algeria (Algiers), Angola (Luanda), Argentina (Buenos Aires), Armenia (Yerevan), Australia(Canberra), Austria (Vienna), Bahrain (Manama), Bangladesh (Dhaka), Bhutan (Thimphu), Bolivia (Sucre), Botswana (Gaborone), Brazil (Brasília), Brunei (Bandar Seri Begawan), Montenegro (Podgorica), Morocco (Rabat), Mozambique (Maputo), Myanmar (Naypyidaw), Namibia (Windhoek), Nepal (Kathmandu), New Zealand (Wellington), Nigeria (Abuja), Oman (Muscat), Palestine (Ramallah), Panama (Panama City), Papua New Guinea (Port Moresby), Paraguay (Asunción), Peru (Lima), Philippines (Manila)¸ Portugal (Lisbon), Qatar (Doha), Rwanda (Kigali), Saudi Arabia (Riyadh), Senegal (Dakar), Serbia (Belgrade), Sierra Leone (Freetown), Slovakia (Bratislava), South Africa (Cape Town) (Pretoria) (Bloemfontein), South Sudan (Juba), Spain (Madrid), Sri Lanka (Sri Jayawardenepura Kotte) (Colombo), Sudan (Khartoum), Syria (Damascus), Tanzania (Dodoma), Thailand (Bangkok), Togo (Lomé), Tonga (Nuku'alofa), Trinidad and Tobago (Port of Spain), Tunisia (Tunis), Turkey (Ankara), Turkmenistan (Ashgabat), Uganda (Kampala), United Arab Emirates (Abu Dhabi), United Kingdom (London), United States (Washington, D.C.)

Last updated: 20 November 2026

Which analog electronics trainers are in this range?

This range lists 29 training boards for electronics and physics laboratories. They cover diode, transistor, MOSFET, UJT and thyristor characteristics, amplifiers, an RF oscillator, networks, resonance and filters, AC bridges and basic circuit laws. Most boards have built-in regulated supplies and run on 230 V mains. Fibre optic link trainers are in the Fiber Optic Trainers range.

Board groups in the analog electronics range

GroupItemsWhat it covers
Diode and opto-electronic device boardsFive boardsDiode and zener characteristics, the energy band gap of a P-N junction, rectifiers with filters, and six opto-electronic devices
Transistor, MOSFET and thyristor boardsSix boardsTransistor characteristics in three modes, MOSFET drain characteristics, and UJT, SCR, TRIAC and DIAC characteristics
Amplifier and oscillator boardsSix boardsEmitter follower, RC coupled, push-pull, differential and multistage BJT amplifiers, and an RF oscillator
Networks, resonance and filtersFour boardsT and pi networks, series and parallel resonance, constant-K and m-derived passive filters, and op-amp active filters
AC bridges and L and C measurementFive boardsAnderson, De Sauty, Wien and Schering bridges and a board for unknown inductance and capacitance
Basic circuit and meter boardsThree boardsOhm's law and series-parallel circuits, capacitor charging and discharging, and galvanometer conversion to an ammeter

Diode and opto-electronic device boards compared

Each board is listed with the values its product page gives. "Not listed" means the page does not state the value.

ProductProduct codeDevicesBuilt-in supplyMetersOther apparatus listed
Training Board for Diode and Zener DiodeJA-AET-1457Germanium diode and zener diode0-10 V DC at 10 mA, continuously variable, with current-limiting resistor3 1/2 digit DC voltmeter (2 V / 20 V) and current meter (2 mA range with 1 µA steps, and 20 mA)Not listed
Semiconductor DiodeJA-AET-1464Germanium and silicon diodes0-10 V DC at 50 mA, with coarse and fine controls3 1/2 digit DC voltmeter (2 V / 20 V) and current meter (0 to 200 µA with 0.1 µA resolution, and 0 to 20 mA)Not listed
Determination of Energy Band Gap in Semiconductor DiodeJA-AET-1460P-N junction diode in an electrically heated oven; 0-110 °C thermometer2 V DC at 10 mA, regulated3 1/2 digit microammeter, 200 microamp rangeNot listed
Junction Diode Rectifier and FilterJA-AET-1468Four silicon junction diodes and a filter chokeMains transformer, 100-0-100 V centre tap at 100 mA3 1/2 digit DC voltmeter (1000 V) and current meter (200 mA)AC millivoltmeter
Opto Electronic DevicesJA-AET-1470LED, photo diode, photo transistor, LDR, photovoltaic cell and opto-couplerTwo 0-10 V DC at 100 mA3 1/2 digit DC voltmeter and two dual range current metersVariac 0-230 V, 2 A; 40 W table lamp

Transistor, MOSFET and thyristor boards compared

ProductProduct codeDeviceWhat students studyBuilt-in suppliesOther apparatus listed
Training Board for TransistorJA-AET-1458Silicon and germanium NPN and PNP transistorsInput and output characteristics in CE, CB and CC modesTwo 0-10 V DC at 50 mA; two voltmeters and two current metersNot listed
Training Board for MOSFETJA-AET-1467MOSFETDrain characteristics; common-source amplifier gain0-15 V, 0-4 V and 0-1 V DC, continuously variableAF generator, AC millivoltmeter, 20 MHz CRO, DC voltmeter and current meter
Unijunction TransistorJA-AET-1465UJTV-I characteristics; relaxation oscillatorTwo 0-30 V DC at 50 mA; 0-30 V voltmeter and 0-5 mA ammeter20 MHz CRO
Silicon Controlled RectifierJA-AET-1459SCRGate and anode characteristics, holding current, phase firing0-50 V DC anode, 0-3 V DC gate and 0-10 V AC supplies; 3 1/2 digit metersVacuum tube voltmeter; 20 MHz CRO
Training Board for TriacJA-AET-1461TRIACGate characteristics in four modes, holding current, static switching0-70 V and 0-3 V DC; 55 V and 7 V AC20 MHz CRO; digital DC current meters and voltmeter
Training Board for DIACJA-AET-1462DIACV-I characteristics, break-over voltage, saw-tooth and pulse generation0-50 V DC; 45 V AC; 0-50 V voltmeter and dual range ammeter20 MHz CRO

Amplifier and oscillator boards compared

ProductProduct codeCircuitActive devices and partsBuilt-in supply or sourceOther apparatus listed
Emitter Follower CCJA-AET-1450Emitter follower (common collector): voltage gain, input and output impedanceNPN transistor+9 V DC at 50 mADecade AF generator; decade resistance box; AF millivoltmeter 0-500 mV
BJT Amplifiers and Emitter Follower TrainerJA-AET-1479Multistage BJT amplifier and emitter followerSocketed 2N3904 NPN and 2N3906 PNP transistors+12 V and +5 V DC; sine wave generator 10 Hz to 100 kHz, 0 to 5 VppNot listed
Two Stage RC Coupled Transistor AmplifierJA-AET-1456Two RC coupled stages: overload and frequency responseTwo PNP transistors-12 V DC, IC regulatedDecade AF generator; AC millivoltmeter; decade resistance box
Push Pull AmplifierJA-AET-1451Class B push-pull audio amplifier: output power, frequency response, distortionThree PNP transistors; driver and output transformers; four switched loads-9 V DC at 50 mADecade AF generator; AC millivoltmeter; output power meter
Differential and Audio Power Amplifier TrainerJA-AET-1476Differential amplifier and audio power amplifierMatched 2N3904 NPN pair; LM386 class-AB audio power amplifier; LM358 op-amp for signal conditioning; optional complementary 2N3904/2N3906 emitter-follower stage+12 V, -12 V, +5 V and -5 V DC; 0 to 1 V variable; sine wave generator 800 Hz to 8 kHzNot listed
RF OscillatorsJA-AET-1452RF oscillator tuned by a variable gang condenserPNP transistor-9 V DC at 50 mAAbsorption wave meter (named on the page)

Network, resonance and filter boards compared

ProductProduct codeCircuitsParts on the panelOther apparatus listed
T and P Network TrainerJA-AET-1449Symmetrical and unsymmetrical T and pi networks: image and characteristic impedance5 V, 150 mA DC supply; terminals and sockets; operating instructionsNot listed
Series and Parallel ResonanceJA-AET-1453Series and parallel resonance curves and QThree ferrite-core inductances, three low-loss capacitances and three resistances, switch-selectedDecade AF generator; AC millivoltmeter; AF millivoltmeter
Passive FiltersJA-AET-1455Constant-K low-pass, high-pass and band-pass; m-derived low-pass and high-passTerminals and sockets for connections and waveform observationAF generator; AC millivoltmeter
Active FiltersJA-AET-1466Op-amp low-pass (1 kHz), high-pass (100 Hz), band-pass (100 Hz to 1 kHz) and notch (1 kHz) filtersFour op-amp ICs; ±12 V DC at 50 mADecade AF generator; AC millivoltmeter

AC bridges and L and C measurement boards compared

ProductProduct codeMeasuresSource and null detectorStandards on the panel
Anderson BridgeJA-AET-1454Inductance of a coilBuilt-in 1 kHz sine oscillator; audio amplifier with speakerThree inductances, a calibrated-dial potentiometer and five band-switched capacitors
De Sauty BridgeJA-AET-1463Ratio of two capacitancesHigh-impedance headphone; needs a separate bridge oscillatorTwo decade resistances (100 ohm steps, 1 kilohm) and two decade capacitors (0.1 microfarad steps, 1 microfarad)
Wien BridgeJA-AET-1473Capacitance with series and parallel Wien bridgesBuilt-in 1 kHz oscillator; audio amplifier and speakerThree decade resistances, a two-dial decade resistance and a switched standard capacitance
Schering Bridge TrainerJA-AET-1475Unknown capacitance by the Schering methodBuilt-in 1 kHz oscillator (0-15 Vpp); audio amplifier and speakerThree unknown capacitors and a six-position resistance selector
Measurement of Inductance and CapacitanceJA-AET-1472Unknown capacitance and inductanceBuilt-in 1 kHz oscillator; audio amplifier and speakerFive unknown capacitors, three unknown inductors and two decade resistances

Basic circuit and meter boards compared

ProductProduct codeExperimentBuilt-in partsOther apparatus listed
Ohm's Law Series and Parallel CircuitsJA-AET-1471Verifying Ohm's law; series and parallel resistive circuits0-15 V DC at 100 mA; 3 1/2 digit DC voltmeter (20 V) and current meter (200 mA)Not listed
Charging and Discharging of a CondenserJA-AET-1469Charging and discharging curves and the time constant0-20 V DC at 25 mA; four electrolytic condensers; three SPDT switchesDigital stop clock; digital DC voltmeter and current meter
Conversion of Galvanometer into an AmmeterJA-AET-1474Galvanometer resistance by half deflection, figure of merit, conversion to an ammeter+5 V DC; 30-0-30 galvanometer; 0-50 mA milliammeterNot listed

How to choose analog electronics trainers

  • For device characteristics, the diode, transistor, MOSFET, UJT, SCR, TRIAC and DIAC boards have their own variable supplies. The band gap board has a fixed 2 V supply instead. Several boards also carry digital or dial meters, so fewer separate instruments are needed.
  • Check the other apparatus each page lists. Most amplifier, resonance and filter boards list an audio frequency generator and an AC or AF millivoltmeter. Several device boards list a 20 MHz CRO.
  • For AC bridges, four boards have a built-in 1 kHz oscillator and an audio null detector: Anderson, Wien, Schering, and the inductance and capacitance board. The De Sauty Bridge uses a headphone and needs a separate bridge oscillator.
  • For a quick amplifier bench, choose the BJT Amplifiers and Emitter Follower Trainer or the Differential and Audio Power Amplifier Trainer. Both have their own sine wave generators.
  • For filter work, compare the Passive Filters board with the Active Filters board. The passive board has constant-K and m-derived sections; the active board uses four op-amp ICs and adds a notch filter.

Practicals covered by the analog boards

PracticalProducts used
Forward and reverse characteristics of germanium, silicon and zener diodesTraining Board for Diode and Zener Diode, Semiconductor Diode
Energy band gap of a P-N junction from its reverse saturation currentDetermination of Energy Band Gap in Semiconductor Diode
Half-wave, full-wave, bridge and voltage doubler rectifiers with filtersJunction Diode Rectifier and Filter
Transistor input and output characteristics; emitter follower gain and impedanceTraining Board for Transistor, Emitter Follower CC
MOSFET drain characteristics and common-source gainTraining Board for MOSFET
UJT, SCR, TRIAC and DIAC characteristicsUnijunction Transistor, Silicon Controlled Rectifier, Training Board for Triac, Training Board for DIAC
Frequency response of RC coupled and push-pull amplifiers; differential and multistage amplifier circuitsTwo Stage RC Coupled Transistor Amplifier, Push Pull Amplifier, Differential and Audio Power Amplifier Trainer, BJT Amplifiers and Emitter Follower Trainer
Resonance curves and Q of series and parallel circuitsSeries and Parallel Resonance
Passive and active filter response and cut-off frequencyPassive Filters, Active Filters
Measuring L and C with Anderson, De Sauty, Wien and Schering bridgesAnderson Bridge, De Sauty Bridge, Wien Bridge, Schering Bridge Trainer, Measurement of Inductance and Capacitance
Ohm's law, capacitor time constant and galvanometer conversionOhm's Law Series and Parallel Circuits, Charging and Discharging of a Condenser, Conversion of Galvanometer into an Ammeter
Characteristics of the LED, photo diode, LDR, photovoltaic cell and opto-couplerOpto Electronic Devices

Who uses these trainers

Electronics and physics laboratories in colleges, polytechnics and engineering institutes use these boards for device, amplifier, filter and network practicals. Ohm's law, capacitor charging and galvanometer conversion are also standard school physics practicals.

Ordering analog electronics trainers

Quote the product code with each board. Most boards run on 230 V, 50 Hz mains.

Add the other apparatus you need, such as audio frequency generators, AC millivoltmeters and oscilloscopes, to the same enquiry. Send the codes and the number of units through our contact page.

Related electronics lab ranges

These boards belong to the Electronics Lab Equipments range from JaincoLab, an electronics lab equipment manufacturer in India.

RangeWhat it covers
Breadboard TrainersDigital and analog breadboard labs, logic trainers, a power project board and a power electronics lab
Digital Electronics TrainerLogic training boards for gates, flip-flops, counters, converters, multiplexers and decoders
Electronic FundamentalsBasic electricity and electronics trainers, base station systems, and op-amp, communications and biomedical trainers
Power Electronics TrainersSCR, triac and UJT trainers, thyristor converters, choppers, inverters and motor speed control
Communication TrainerAM, FM, pulse and digital modulation trainers, multiplexing, transmission line and LAN trainers
Fiber Optic TrainersFibre optic link and transceiver trainers, a numerical aperture trainer and a fibre optic power meter
Oscilloscopes30 MHz and 20 MHz dual trace oscilloscopes, an oscilloscope with digital readout and a frequency counter
Digital Storage OscilloscopesDigital storage oscilloscopes, including dual channel and four channel models
Signal GeneratorsFunction generators, an AM and FM function generator and an RF signal generator
Radio and Telephone CommunicationsAM FM radio, CB transceiver, walkie talkie, mobile phone and microwave trainers
Audio and Visual TechnologyTelevision, audio, DVD, video camera, CCTV and intercom trainers
Electrical TechnologyElectrical measurement, transformer and metering, and appliance repair trainers
Wiring, Distribution and ProtectionElectrical installation, circuit fault and electrical machine trainers
Data Acquisition, Instrumentation and Process ControlPLC trainers, a conveyor system, process panels and temperature and level control trainers
Variac DimmerstatsSingle phase and three phase variacs in panel and portable types

Frequently Asked Questions

How do you plot the forward and reverse characteristics of a diode on a trainer?
Connect the diode in forward bias, raise the supply in small steps and record the current at each step. Then reverse the diode and repeat over a wider voltage range. Plot current against voltage: the forward curve rises sharply after the knee. The diode boards have a built-in variable supply and digital meters for this.

Why is a capacitor filter used after a rectifier, and what causes ripple?
A rectifier gives pulsating DC. The capacitor charges near each peak and discharges into the load between peaks, which smooths the output. The small rise and fall that remains is ripple. A larger capacitor or a lighter load gives less ripple. The Junction Diode Rectifier and Filter board compares ripple across its rectifier circuits.

Which transistor configuration gives the highest voltage gain: CE, CB or CC?
Common emitter and common base both give high voltage gain. Common emitter also gives current gain, so it has the highest power gain and is used most. Common collector, the emitter follower, has a voltage gain just below one. Its high input and low output impedance make it a buffer.

How should students find the fault when an amplifier circuit gives no output?
Start with the supply and check the DC voltage on the board. Next measure the transistor bias voltages and compare them with the expected values. Then feed in a signal and follow it stage by stage on an oscilloscope. The fault lies between the last good point and the first bad one.

Will a separate signal generator and meters have to be ordered with the analog trainers?
It depends on the board. Most boards have built-in regulated supplies, and many device boards have meters. Most amplifier, resonance and filter boards list an audio frequency generator and an AC or AF millivoltmeter. Several device boards list a 20 MHz CRO. Two amplifier trainers and most bridge boards have their own signal source.

Should a tender for analog trainers ask for short-circuit protection on the supply outputs?
Yes, because students often short supply terminals by mistake. Most mains-powered boards list a fuse on the mains side. The diode and zener board's supply has a current-limiting resistor, and the SCR board has fixed limiting resistances. Name the protection you need in the tender and in your enquiry.

For a quotation, list the boards with their product codes and the number of units, and send the list through our contact page. For tender or project supply, see our tenders page.

T and P Network Trainer

T and P Network Trainer

Product Code : JA-AET-1449

The T and pi network trainer is a panel for verifying the impedance properties of passive T and pi networks in electronics and network theory practicals.

Note: The T and pi network trainer is a panel for verifying the impedance properties of passive T and pi networks in electronics and network theory practicals.

View Details
Emitter Follower CC

Emitter Follower CC

Product Code : JA-AET-1450

The emitter follower trainer is a common-collector (CC) amplifier board for measuring voltage gain, input impedance and output impedance in electronics practicals.

Note: The emitter follower trainer is a common-collector (CC) amplifier board for measuring voltage gain, input impedance and output impedance in electronics practicals.

View Details
Push Pull Amplifier

Push Pull Amplifier

Product Code : JA-AET-1451

The push pull amplifier trainer is a class B transistor push-pull amplifier board for audio-frequency practicals.

Note: The push pull amplifier trainer is a class B transistor push-pull amplifier board for audio-frequency practicals.

View Details
RF Oscillators

RF Oscillators

Product Code : JA-AET-1452

The RF oscillators board is a panel for radio-frequency oscillator practicals, built around a PNP transistor with a variable gang condenser and an internally connected -9 V DC, 50 mA IC-regulated supply.

Note: The RF oscillators board is a panel for radio-frequency oscillator practicals, built around a PNP transistor with a variable gang condenser and an internally connected -9 V DC, 50 mA IC-regulated supply.

View Details
Series and Parallel Resonance

Series and Parallel Resonance

Product Code : JA-AET-1453

The series and parallel resonance trainer lets students plot resonance curves for series and parallel circuits with different values of resistance, capacitance and inductance, and measure Q for both.

Note: The series and parallel resonance trainer lets students plot resonance curves for series and parallel circuits with different values of resistance, capacitance and inductance, and measure Q for both.

View Details
Anderson Bridge

Anderson Bridge

Product Code : JA-AET-1454

The Anderson bridge trainer measures the inductance of a coil by the Anderson bridge method.

Note: The Anderson bridge trainer measures the inductance of a coil by the Anderson bridge method.

View Details
Passive Filters

Passive Filters

Product Code : JA-AET-1455

The passive filters trainer is used to study constant-K and m-derived passive filters and to determine their constants and cut-off frequencies.

Note: The passive filters trainer is used to study constant-K and m-derived passive filters and to determine their constants and cut-off frequencies.

View Details
Two Stage RC Coupled Transistor Amplifier

Two Stage RC Coupled Transistor Amplifier

Product Code : JA-AET-1456

The two stage RC coupled transistor amplifier trainer is a board with two PNP transistor stages for studying the characteristics of a cascade amplifier.

Note: The two stage RC coupled transistor amplifier trainer is a board with two PNP transistor stages for studying the characteristics of a cascade amplifier.

View Details
Training Board for Diode and Zener Diode

Training Board for Diode and Zener Diode

Product Code : JA-AET-1457

Board for plotting forward and reverse characteristics of a germanium diode and a zener diode: 0 to 10 V, 10 mA regulated supply, 3½ digit voltmeter (2 V, 20 V) and current meter (2 mA with 1 µA steps, 20 mA).

Note: Diode and zener characteristics board with built-in supply and meters, manufactured by JaincoLab.

View Details
Training Board for Transistor

Training Board for Transistor

Product Code : JA-AET-1458

The transistor training board is used to study and plot transistor input and output characteristics in common emitter, common base and common collector modes.

Note: The transistor training board is used to study and plot transistor input and output characteristics in common emitter, common base and common collector modes.

View Details
Silicon Controlled Rectifier

Silicon Controlled Rectifier

Product Code : JA-AET-1459

The SCR characteristics trainer is used to study the DC gate (firing) characteristics and anode current characteristics of a silicon controlled rectifier, measure its holding current and plot its phase firing characteristics.

Note: The SCR characteristics trainer is used to study the DC gate (firing) characteristics and anode current characteristics of a silicon controlled rectifier, measure its holding current and plot its phase firing characteristics.

View Details
Determination of Energy Band Gap in Semiconductor Diode

Determination of Energy Band Gap in Semiconductor Diode

Product Code : JA-AET-1460

The energy band gap trainer determines the energy band gap of a P-N junction diode from its reverse saturation current at different temperatures.

Note: The energy band gap trainer determines the energy band gap of a P-N junction diode from its reverse saturation current at different temperatures.

View Details
Training Board for Triac

Training Board for Triac

Product Code : JA-AET-1461

The TRIAC training board is used to study the gate characteristics of a TRIAC in modes I+, I-, III+ and III-, its terminal characteristics in modes I+ and III+, and its holding current.

Note: The TRIAC training board is used to study the gate characteristics of a TRIAC in modes I+, I-, III+ and III-, its terminal characteristics in modes I+ and III+, and its holding current.

View Details
Training Board for DIAC

Training Board for DIAC

Product Code : JA-AET-1462

The DIAC training board is used to plot the V-I characteristics of a DIAC and study its break-over voltage, negative resistance region and VBO symmetry.

Note: The DIAC training board is used to plot the V-I characteristics of a DIAC and study its break-over voltage, negative resistance region and VBO symmetry.

View Details
De Sauty Bridge

De Sauty Bridge

Product Code : JA-AET-1463

The De Sauty bridge trainer is used to study the working of a De Sauty bridge and to compare the capacitances of two capacitors.

Note: The De Sauty bridge trainer is used to study the working of a De Sauty bridge and to compare the capacitances of two capacitors.

View Details
Semiconductor Diode

Semiconductor Diode

Product Code : JA-AET-1464

Trainer for forward and reverse characteristics of a germanium diode and a 1N4148 silicon diode, with static and dynamic resistance: current-limited 0 to 10 V, 50 mA supply, 3½ digit voltmeter (2 V, 20 V) and current meter (200 µA and 20 mA).

Note: Diode characteristics trainer with germanium and 1N4148 silicon diodes, manufactured by JaincoLab.

View Details
Unijunction Transistor

Unijunction Transistor

Product Code : JA-AET-1465

The UJT trainer is used to plot the V-I characteristics of a unijunction transistor and to use it as a relaxation oscillator.

Note: The UJT trainer is used to plot the V-I characteristics of a unijunction transistor and to use it as a relaxation oscillator.

View Details
Active Filters

Active Filters

Product Code : JA-AET-1466

The active filters trainer is used to study the characteristics of op-amp active filters: a 1 kHz low-pass, a 100 Hz high-pass, a 100 Hz to 1 kHz band-pass and a 1 kHz notch filter.

Note: The active filters trainer is used to study the characteristics of op-amp active filters: a 1 kHz low-pass, a 100 Hz high-pass, a 100 Hz to 1 kHz band-pass and a 1 kHz notch filter.

View Details
Training Board for MOSFET

Training Board for MOSFET

Product Code : JA-AET-1467

The MOSFET training board is used to determine the drain characteristics of a MOSFET and to use it as a common-source amplifier, measuring its voltage gain.

Note: The MOSFET training board is used to determine the drain characteristics of a MOSFET and to use it as a common-source amplifier, measuring its voltage gain.

View Details
Junction Diode Rectifier and Filter

Junction Diode Rectifier and Filter

Product Code : JA-AET-1468

The junction diode rectifier and filter trainer compares half-wave, centre-tap full-wave, bridge full-wave and voltage doubler rectifiers, measuring output and ripple content with different resistive loads.

Note: The junction diode rectifier and filter trainer compares half-wave, centre-tap full-wave, bridge full-wave and voltage doubler rectifiers, measuring output and ripple content with different resistive loads.

View Details
Charging and Discharging of a Condenser

Charging and Discharging of a Condenser

Product Code : JA-AET-1469

The capacitor charging and discharging trainer is used to plot voltage and current against time while a condenser charges and discharges, and to find the time constant from each graph.

Note: The capacitor charging and discharging trainer is used to plot voltage and current against time while a condenser charges and discharges, and to find the time constant from each graph.

View Details
Opto Electronic Devices

Opto Electronic Devices

Product Code : JA-AET-1470

The opto-electronic devices trainer is used to study the characteristics of six devices: an LED, a photo diode, a photo transistor, an LDR, a photovoltaic cell and an opto-coupler.

Note: The opto-electronic devices trainer is used to study the characteristics of six devices: an LED, a photo diode, a photo transistor, an LDR, a photovoltaic cell and an opto-coupler.

View Details
Ohm's Law Series and Parallel Circuits

Ohm's Law Series and Parallel Circuits

Product Code : JA-AET-1471

The Ohm's law and series-parallel circuits trainer is used to verify Ohm's law and to study series and parallel resistive circuits.

Note: The Ohm's law and series-parallel circuits trainer is used to verify Ohm's law and to study series and parallel resistive circuits.

View Details
Measurement of Inductance and Capacitance

Measurement of Inductance and Capacitance

Product Code : JA-AET-1472

The inductance and capacitance measurement trainer is a bridge panel for measuring unknown capacitances and unknown inductances.

Note: The inductance and capacitance measurement trainer is a bridge panel for measuring unknown capacitances and unknown inductances.

View Details
Wien Bridge

Wien Bridge

Product Code : JA-AET-1473

The Wien bridge trainer is used to study the Wien bridge and to measure capacitance with both the Wien series bridge and the Wien parallel bridge.

Note: The Wien bridge trainer is used to study the Wien bridge and to measure capacitance with both the Wien series bridge and the Wien parallel bridge.

View Details
Conversion of Galvanometer into an Ammeter

Conversion of Galvanometer into an Ammeter

Product Code : JA-AET-1474

This trainer is used to determine the resistance of a galvanometer by the half-deflection method, find its figure of merit, and convert it into an ammeter of a given range and calibrate it.

Note: This trainer is used to determine the resistance of a galvanometer by the half-deflection method, find its figure of merit, and convert it into an ammeter of a given range and calibrate it.

View Details
Schering Bridge Trainer

Schering Bridge Trainer

Product Code : JA-AET-1475

The Schering bridge trainer measures unknown capacitance by the Schering bridge method.

Note: The Schering bridge trainer measures unknown capacitance by the Schering bridge method.

View Details
Differential and Audio Power Amplifier Trainer

Differential and Audio Power Amplifier Trainer

Product Code : JA-AET-1476

Trainer for a differential amplifier and an audio power amplifier: matched 2N3904 pair, LM386 class-AB audio stage, LM358 for signal conditioning, built-in +12, -12, +5 and -5 V and 0 to 1 V supplies, 800 Hz to 8 kHz sine generator. 230 V, 50 Hz.

Note: Analogue trainer for differential amplifier and LM386 audio power amplifier practicals, manufactured by JaincoLab.

View Details
BJT Amplifiers and Emitter Follower Trainer

BJT Amplifiers and Emitter Follower Trainer

Product Code : JA-AET-1479

Trainer for a multistage BJT amplifier and an emitter follower: socketed 2N3904 and 2N3906 transistors, built-in +12 V and +5 V supplies, 10 Hz to 100 kHz sine generator at 0 to 5 Vpp. 230 V, 50 Hz, 500 mA fuse.

Note: BJT amplifier and emitter follower trainer for analogue electronics practicals, manufactured by JaincoLab.

View Details

Office Address

Jain Scientific Suppliers
2475-84, Hargolal Road,
Ambala Cantt, Haryana, India

[email protected]

+91-85699-09696

Follow Us