Cellular Mobile Phone Trainer
Product Code : JA-RATC-9596
The Cellular Mobile Phone Trainer teaches service technicians how a mobile handset works and how its faults are found and repaired. It is offered in two versions. The legacy trainer uses a modified GSM handset with test points and a fault board. The LTE version places a Band 3 lab device in a shielded coupling box.
Specifications of the cellular mobile phone trainer
| Product code | JA-RATC-9596 |
|---|---|
| Order options | Legacy GSM/CDMA trainer, or LTE Band 3 lab version |
| Legacy version: handsets | Modified GSM handset (900/1800 MHz class), with a CDMA handset where one can be sourced; network service and bands as the actual handset supports |
| Legacy version: training hardware | Easy access to internal components, test points, controlled fault board for electronic fault insertion, battery and isolated adapter |
| LTE version: device | One LTE Band 3 lab device in a shielded coupling box, on a conducted test platform |
| LTE Band 3 frequencies | Uplink 1710 to 1785 MHz; downlink 1805 to 1880 MHz |
| LTE version: RF settings | Channel bandwidth and power set by the selected test system; no public-network transmit power and no live-network access |
| LTE version: exercises | Data and call demonstration, power and charging block, fault exercises |
| Course coverage | Operation, theory, programming, servicing, diagnosis and repair |
| Documentation | Repair guide |
| Manufacturer | JaincoLab, Ambala, India |
Servicing practicals on the cellular mobile phone trainer
- Current at switch-on. Power the handset from a bench supply set to its battery voltage, with the Digital Multimeter in series on its current range. A reading that stays at zero or jumps high points to the power section.
- Fault insertion. Switch in a fault on the fault board, note the symptom, then trace it at the test points with the meter. Record the fault, the readings and the repair in the guide.
- Signals at the test points. View the clock and data lines at the test points on the Digital Storage Oscilloscope 40MHz and compare them with the repair guide.
- From landline to cellular. Compare call set-up on the Telephone Trainer with registration and call set-up on the cellular trainer. List what the mobile network adds at each step.
Frequently Asked Questions
Why does LTE Band 3 use separate uplink and downlink frequencies?
Band 3 is a frequency-division duplex band. The handset transmits on the uplink, 1710 to 1785 MHz, and receives on the downlink, 1805 to 1880 MHz, at the same time. The gap between the two keeps the strong transmit signal out of the sensitive receiver.
How do students trace a no-network fault on the legacy handset?
Start with the simple causes: the SIM, the antenna contact and the software. Then check the supply rails to the RF section at the test points, and the signals around the transceiver and power amplifier. The fault board lets the teacher set a known network fault, so students can practise the sequence safely.
What can a multimeter tell us about a phone that will not power on?
On the current range, in series with the supply, it shows whether the phone draws nothing, a normal start-up current or a short-circuit current. On the voltage range it checks each supply rail at the test points. On resistance, with the power off, it finds shorted capacitors.
What does the SIM do when a handset registers on a network?
The SIM holds the subscriber identity and a secret key. During registration the network sends a challenge, the SIM answers it with the key, and the network compares that answer with its own. Only then does it accept the handset for calls and data.
Do the cellular trainers need an import permit or type approval?
Usually, yes. Both versions contain a radio transmitter, and radio transmitters usually need an import licence or type approval in the buyer's country. Some countries also limit how many handsets may be brought in. Check with your telecom regulator before ordering.
What should we tell the regulator about the LTE lab version?
Say that it is one LTE Band 3 lab device inside a shielded coupling box, on a conducted test platform. Channel bandwidth and power are set by the test system, and it has no public-network transmit power or live-network access. Quote the product code JA-RATC-9596 and the version on every document.
Other trainers in the radio and telephone range
- CB Transceiver Trainer
- AM FM Radio Trainer
- Radio Communication Training System
- Integrated AM and FM Trainer
- Walkie Talkie Trainer
- Antenna System Demonstrator
JaincoLab supports tender contractors as well as institutions: we manufacture and export laboratory equipment for Ministry of Education projects, World Bank-funded tenders and United Nations programmes, executed successfully in many countries, and we specialise in turnkey laboratory set-ups. Contact us through the tenders page early in your bid preparation.
See the Radio and Telephone Communications range and more electronics lab equipment from JaincoLab, an electronics lab equipment manufacturer in India.
For a quotation, send the product name and the quantity you need through our contact page. For tender or project supply, see our tenders page.
