AM FM Radio Trainer
Product Code : JA-RATC-9591
The AM FM Radio Trainer is a working superheterodyne receiver laid out for teaching. One receive chain switches between AM medium wave and FM, with test points at the RF, mixer, IF, detector and audio stages. Students follow a signal from the antenna to the loudspeaker, then find faults stage by stage.
Specifications of the AM FM radio trainer
| Product code | JA-RATC-9591 |
|---|---|
| Receiver type | Superheterodyne AM/FM receiver with one receive chain, switched between AM and FM |
| AM band | Medium wave, 530 to 1710 kHz, in 9 or 10 kHz tuning steps to suit the market, or continuous tuning; set for the destination |
| FM band | 88 to 108 MHz, continuous tuning |
| Transmit power | 0 W; receiver only, with no transmitter |
| Test points | RF, mixer, IF, detector and audio stages |
| Supplied with | Antenna and loudspeaker |
| Power supply | 9 V DC source |
| Construction | Circuits on easily accessible printed circuit boards |
| Documentation | Workbook, manuals and experiment sheets covering theory, operation, testing and troubleshooting |
| Manufacturer | JaincoLab, Ambala, India |
Receiver practicals on the AM FM radio trainer
- Voltage survey. With the 9 V supply on, measure the DC voltage at each stage with a Digital Multimeter and record it against the manual. A missing or wrong voltage points to the stage to check first.
- Signal injection. Feed a modulated signal from the 150 MHz RF Signal Generator into the audio, detector, IF and mixer test points in turn. Work back from the loudspeaker. The first point where the tone disappears marks the faulty stage.
- Signal tracing. Tune in a station and follow it forward through the receiver with the Signal Tracer or the 30 MHz Oscilloscope. Compare the signal at each test point with the sketches in the workbook.
- AM and FM compared. Switch between the bands and compare the IF and detector waveforms. The FM signal keeps a constant amplitude, while AM carries the sound in its envelope.
Frequently Asked Questions
What is image frequency in an AM or FM receiver?
The mixer produces the IF from two input frequencies. One is the wanted station; the other lies twice the IF away, on the far side of the local oscillator. That second signal is the image. Tuned circuits before the mixer weaken it, and a higher IF moves it further away, so it is easier to reject.
Why does the radio convert every station to one fixed intermediate frequency?
Amplifiers and filters give steady gain and selectivity when they are tuned once to a single frequency. By moving the local oscillator, every station is shifted to the same IF, where the main gain and selectivity are set and never retuned. Only the front end and the oscillator follow the tuning dial.
How does the detector differ between AM and FM reception?
An AM detector follows the envelope of the IF signal, usually with a diode and a small filter capacitor. FM carries the sound in changes of frequency, so its detector must turn frequency into voltage, as a discriminator or ratio detector does. A limiter before the FM detector strips off amplitude noise.
Can students align the radio themselves?
Yes, as an advanced exercise under supervision. A signal generator supplies the IF and band-edge frequencies, and the cores and trimmers are adjusted for the loudest clean output. Mark the original positions first, so the set can be brought back to its starting alignment if needed.
Does the AM FM Radio Trainer need a radio licence to import?
It is a receiver only, with an RF transmit power of 0 W, so it sends nothing on air. Rules for importing receivers still differ by country, so check with your telecom regulator or customs broker before ordering. Tell us the destination, and the AM band is set for that market.
How do distributors ask for a bulk quotation for class sets?
Send the number of trainers and the destination through our contact page. JaincoLab also makes custom kits for distributors and for education projects. A sample unit can be sent with the quotation, so you can evaluate it first.
Other trainers in the radio and telephone range
- CB Transceiver Trainer
- Radio Communication Training System
- Integrated AM and FM Trainer
- Walkie Talkie Trainer
- Antenna System Demonstrator
- Cellular Mobile Phone Trainer
Contractors bidding for education-ministry, World Bank or United Nations laboratory tenders can source the complete equipment list from JaincoLab. We manufacture and export for these projects, have delivered them successfully in many countries and specialise in turnkey laboratory supply.
See the Radio and Telephone Communications range and more electronics lab equipment from JaincoLab, an electronics lab equipment manufacturer in India.
For a quotation, send the product name and the quantity you need through our contact page. For tender or project supply, see our tenders page.
