70 MHz Digital Storage Oscilloscope
Product Code : JA-DSO-1535
The 70 MHz Digital Storage Oscilloscope is a two-channel DSO with 2 GSa/s real-time sampling, a 24k memory depth and a 7-inch colour TFT display. It triggers on edge, pulse, video, slope, alternative and delay events. It adds 32 automatic measurements, FFT, a digital filter, pass/fail testing and a waveform recorder.
Specifications of the 70 MHz digital storage oscilloscope
| Product code | JA-DSO-1535 |
|---|---|
| Bandwidth | 70 MHz (dual-channel family from 70 MHz to 300 MHz) |
| Channels | 2 |
| Sampling and memory | 2 GSa/s real time; 24k memory depth |
| Display | 7-inch colour TFT LCD; pop-up menus, multilingual interface and online help |
| Vertical sensitivity and input | About 2 mV/div to 10 V/div; 1 Mohm input* |
| Triggering | Edge, pulse, video, slope, alternative and delay |
| Analysis | 32 automatic parameters; cursors in manual, track and auto modes; digital filter; waveform recorder; pass/fail; waveform and FFT on a split screen |
| Interfaces | USB host and device, front and back; GPIB |
| Power and probes | 100 to 240 V AC, 50/60 Hz universal input; one correctly rated 10x passive probe per channel* |
| Manufacturer | JaincoLab, Ambala, India |
* Standard JaincoLab specification for new builds.
Uses of the 70 MHz DSO in the electronics laboratory
- Pulse width capture. On the Pulse Width Modulation and Demodulation board, set the pulse trigger to catch pulses wider than a chosen limit. Measure the duty cycle of each captured pulse with the automatic parameters.
- Small signals and the digital filter. Show a low-level sine from the 5 MHz Function Generator on a sensitive range. Switch the digital filter on and off and compare the noise on the trace.
- Phase shift of an active filter. Drive the Active Filters board and show its input and output together. Measure the time shift with the cursors as the frequency rises.
- A modulated signal with FFT. View the output of the Frequency Modulation and Demodulation Trainer with FFT on the split screen, and watch the spectrum widen as the deviation grows.
Frequently Asked Questions
How many samples per cycle does a 2 GSa/s scope take of a 70 MHz sine?
About twenty-eight. Two thousand million samples per second divided by seventy million cycles per second gives roughly that many points in each cycle. That is enough to draw a sine cleanly. Sine interpolation joins the points, so the trace stays smooth at the top of the bandwidth.
How do students set up a pass/fail mask from a good waveform?
Show a known good waveform, then build the mask from it with a set margin in time and in voltage. The scope compares every new trace with the mask and counts passes and failures. Choose whether it stops, carries on or saves the waveform when a trace fails.
Which trigger slope should be used to catch a falling edge?
Set the edge trigger to the falling slope. The scope then starts each trace when the signal passes the trigger level on its way down. With the rising slope, the same square wave is drawn from its rising edge, so the picture shifts by half a cycle.
What routine checks should a lab technician make on a class set of oscilloscopes?
Switch each scope on and watch the start-up screen for error messages. Show a known square wave on both channels with their probes, and check the amplitude and frequency readings. Record the results in the lab log, and take any scope that fails out of use until it is serviced.
Which customs heading do importers use for this digital oscilloscope?
Oscilloscopes have their own subheading in the customs tariff, among instruments for measuring electrical quantities. National digits after the first six differ by country, so confirm the full code with your customs broker. Describe the goods on the invoice as a two-channel, 70 MHz digital storage oscilloscope.
What memory and display figures should a tender give for the 70 MHz model?
Give a 24k memory depth, 2 GSa/s real-time sampling and a 7-inch colour TFT display, with two analogue channels and 70 MHz bandwidth. If your tender asks for a wider bandwidth, the same dual-channel family goes up to 300 MHz.
Other digital storage oscilloscopes in the range
- Digital Storage Oscilloscope Dual Channel
- Dual Channel Digital Storage Oscilloscope 100 to 300 MHz
- 200 MHz Digital Storage Oscilloscope
- 300 MHz Digital Storage Oscilloscope
See the Digital Storage Oscilloscopes range and more electronics lab equipment from JaincoLab, an electronics lab equipment manufacturer in India.
For a quotation, send the product name and the quantity you need through our contact page. For tender or project supply, see our tenders page.
