• +91-85699-09696

Temperature Process Control Trainer

Temperature Process Control Trainer

Product Code : JA-DAIAPC-9616

Students use the Temperature Process Control Trainer to learn process control by tuning a loop that holds water at a set temperature. It is a closed-loop water heating bench with a 5 L insulated vessel, a 500 W heater, a Pt100 temperature probe and a PID controller. All components are laid out on a vertical front panel with a large-format process diagram.

Specifications of the Temperature Process Control Trainer

Product codeJA-DAIAPC-9616
Process and layoutClosed-loop water heating bench for temperature control; components on a vertical front panel with a large-format process diagram
Vessel5 L insulated water vessel
Heater500 W electric heater
Temperature probePt100 RTD probe, 3-wire, Class A, in a stainless-steel immersion sheath; sensor range 0 to 150°C, control and display range 0 to 100°C for the water-heating experiment*
ControllerPID controller with readout
CirculationRecirculation pump
ProtectionHigh-limit protection on the heater; independent over-temperature cut-out and dry-heating protection*
Data loggingUSB logging, as an option
Mains supply (this configuration)230 V AC, 50 Hz, single phase, for the 500 W heater configuration; supply connection rated at least 5 A, with a suitable fuse and protective earth*
ManufacturerJaincoLab, Ambala, India

* Standard JaincoLab specification for new builds.

Temperature control experiments on the trainer

  • Open-loop heating curve. Fill the vessel and start the pump before the heater is switched on. With the controller in manual, set a fixed heater output and read the temperature at regular intervals, timed with a Digital Stop Watch. Plot the curve and mark the dead time and the time constant. Hot water can scald, so let the water cool before the vessel is drained.
  • Probe check. Place a Digital Stem Thermometer in the vessel beside the temperature probe. Compare the two readings with cool water and again with warm water before any control run.
  • From P to PID. Run the loop with proportional action only and note the offset from the setpoint. Add integral action, then derivative action, and compare the overshoot and the settling time each time.
  • Comparing two loops. Repeat the tuning on the Level Process Control Trainer and compare how fast each loop answers a step change in setpoint.

Frequently Asked Questions

Why does the trainer use a 3-wire Pt100 probe for the water temperature?
A Pt100 is a platinum resistance sensor that reads 100 ohm at 0°C. Its resistance rises almost in a straight line with temperature and stays stable for years. In the 3-wire connection the controller allows for the resistance of the leads, so long leads do not add a false temperature. A thermocouple version is a separate model with its own controller input and compensation.

Why does the water temperature keep swinging above and below the setpoint with on-off control?
An on-off controller switches the heater fully on below the setpoint and fully off above it. Heat stored in the heater and the water keeps the temperature rising after switch-off, and falling for a while after switch-on. The result is a steady swing, which PID control reduces.

How does the water flow rate change how fast the loop heats up and cools down?
A faster flow carries heat from the heater to the probe sooner, so the controller sees each change earlier and the dead time is shorter. A slow flow lets warm and cool layers form in the vessel. The probe then lags behind the real water temperature and the loop is harder to tune.

What should be checked before switching the temperature loop to automatic control?
Fill the vessel and run the recirculation pump first, so the heater is never on in an empty vessel. Check that the probe reading agrees with a reference thermometer and that the heater responds to a manual output. Then confirm the high-limit protection before handing control to the PID.

What is included in the scope of supply of the temperature trainer?
The trainer is a closed-loop water heating bench on a front panel with a process diagram. It has a 5 L insulated vessel, a 500 W heater and a 3-wire Pt100 probe. A PID controller with readout, a recirculation pump and high-limit protection complete it. USB logging is an option, so list it in your enquiry if you need it.

What mains supply does the 500 W temperature trainer need?
This configuration runs on 230 V AC, 50 Hz single-phase mains. The 500 W heater alone draws about 2.17 A, and the pump and controller add to that. The supply point should be rated at least 5 A and have a protective earth. Another mains voltage means a separate electrical version, so state yours in the enquiry.

Level control and PLC trainers in the same range

JaincoLab manufactures and exports laboratory equipment for Ministry of Education programmes, World Bank-funded tenders and United Nations projects, and has executed these supplies successfully in many countries. Contractors bidding for such tenders can contact JaincoLab for specifications, quotations and turnkey tender supply.

See the Data Acquisition, Instrumentation and Process Control range and more electronics lab equipment from JaincoLab, an electronics lab equipment manufacturer in India.

For a quotation, send the product name and the quantity you need through our contact page. For tender or project supply, see our tenders page.

Last updated: 20 November 2026

   
Supply of Temperature Process Control Trainer from to Finland, France, Tanzania, Thailand, Sri Lanka, Congo, Costa Rica, Ivory Coast, Croatia, Cuba, Cyprus, Czech Republic, Denmark, Djibouti, Dominica, Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Bangladesh, Barbados, United Arab Emirates (UAE, Dubai), United Kingdom (London), United States, Uruguay, Uzbekistan, Vanuatu, Belarus, Belgium, Belize, Benin, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, Brunei, Bulgaria, Burkina Faso, Burma Myanmar, East Timor, Ecuador, Egypt, El Salvador, Equatorial Guinea, Eritrea, Estonia, Ethiopia (Addis Ababa), Fiji, Burundi, Cambodia, Cameroon, Canada, Cape Verde, Central African Republic, Chad, Chile, Colombia. Math Teaching Kit suppliers in Luxembourg, Macedonia, Madagascar, Malawi (Lilongwe), Malaysia (Kuala Lumpur), Maldives, Mali, Malta, Marshall Islands, Mauritania, Mexico, Micronesia, Moldova, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Comoros, Congo. Math Teaching Kit manufacturers in Dominican Republic, Gabon, Gambia, Georgia, Germany, Ghana, Greece, Grenada, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hungary, Iceland, Indonesia, Iran, Iraq, Niger, Nigeria (Abuja), Norway, Oman, Palau, Panama, Papua New Guinea, Paraguay, Peru, Philippines (Manila), Poland, Ireland, Israel, Italy, Jamaica, Japan, Jordan, Kazakhstan, Kenya (Nairobi), Kiribati, Korea, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Mauritius, Nauru, Nepal, Netherlands, New Zealand, Nicaragua, Portugal, Qatar, Romania, Russia, Rwanda (Kigali). Math Teaching Kit exportets to Saint Kitts and Nevis, Saint Lucia, Saint Vincent and the Grenadines, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, Solomon Islands, Somalia, South Africa, South Sudan, Spain, Sudan, Suriname, Swaziland, Sweden, Switzerland, Syria, Tajikistan, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda (Kampala), Ukraine, Venezuela, Vietnam, Yemen , Zambia (Lusaka), Zimbabwe

Office Address

Jain Scientific Suppliers
2475-84, Hargolal Road,
Ambala Cantt, Haryana, India

[email protected]

+91-85699-09696

Follow Us